# File generated by xf86config and modified by PJT Section "Files" RgbPath "/usr/X11R6/lib/X11/rgb" FontPath "/usr/X11R6/lib/X11/fonts/misc/" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled" FontPath "/usr/X11R6/lib/X11/fonts/75dpi/" # For OSs that support Dynamically loaded modules, ModulePath can be # used to set a search path for the modules. This is currently supported # for Linux ELF, FreeBSD 2.x and NetBSD 1.x. The default path is shown # here. # ModulePath "/usr/X11R6/lib/modules" EndSection # ********************************************************************** # Module section -- this is an optional section which is used to specify # which dynamically loadable modules to load. Dynamically loadable # modules are currently supported only for Linux ELF, FreeBSD 2.x # and NetBSD 1.x. Currently, dynamically loadable modules are used # only for some extended input (XInput) device drivers. # ********************************************************************** # # Section "Module" # # This loads the module for the Joystick driver # # Load "xf86Jstk.so" # # EndSection # ********************************************************************** # Server flags section. # ********************************************************************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # NoTrapSignals # Uncomment this to disable the server abort sequence # This allows clients to receive this key event. # DontZap # Uncomment this to disable the / mode switching # sequences. This allows clients to receive these key events. # DontZoom # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # DisableVidModeExtension # Uncomment this to enable the use of a non-local xvidtune client. # AllowNonLocalXvidtune # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # DisableModInDev # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # AllowNonLocalModInDev EndSection # ********************************************************************** # Input devices # ********************************************************************** # ********************************************************************** # Keyboard section # ********************************************************************** Section "Keyboard" Protocol "Standard" # when using XQUEUE, comment out the above line, and uncomment the # following line # Protocol "Xqueue" AutoRepeat 500 5 # Let the server do the NumLock processing. This should only be required # when using pre-R6 clients # ServerNumLock # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Xleds 1 2 3 # To set the LeftAlt to Meta, RightAlt key to ModeShift, # RightCtl key to Compose, and ScrollLock key to ModeLock: # LeftAlt Meta # RightAlt ModeShift # RightCtl Compose # ScrollLock ModeLock # To disable the XKEYBOARD extension, uncomment XkbDisable. XkbDisable # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # XkbModel "pc102" # If you have a US Microsoft Natural keyboard, you can use: # XkbModel "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # XkbLayout "de" # or: # XkbLayout "de" # XkbVariant "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # XkbOptions "ctrl:swapcaps" # These are the default XKB settings for XFree86 # XkbRules "xfree86" # XkbModel "pc101" # XkbLayout "us" # XkbVariant "" # XkbOptions "" XkbKeymap "xfree86(us)" EndSection # ********************************************************************** # Pointer section # ********************************************************************** Section "Pointer" Protocol "PS/2" Device "/dev/mouse" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Protocol "Xqueue" # Baudrate and SampleRate are only for some Logitech mice # BaudRate 9600 # SampleRate 150 # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) Emulate3Buttons Emulate3Timeout 50 # ChordMiddle is an option for some 3-button Logitech mice # ChordMiddle EndSection # ********************************************************************** # Xinput section -- this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the XF86Config man page for a description of the options. # ********************************************************************** # # Section "Xinput" # SubSection "WacomStylus" # Port "/dev/ttyS1" # DeviceName "Wacom" # EndSubSection # SubSection "WacomCursor" # Port "/dev/ttyS1" # EndSubSection # SubSection "WacomEraser" # Port "/dev/ttyS1" # EndSubSection # # SubSection "Elographics" # Port "/dev/ttyS1" # DeviceName "Elo" # MinimumXPosition 300 # MaximumXPosition 3500 # MinimumYPosition 300 # MaximumYPosition 3500 # Screen 0 # UntouchDelay 10 # ReportDelay 10 # EndSubSection # # SubSection "Joystick" # Port "/dev/joy0" # DeviceName "Joystick" # TimeOut 10 # MinimumXPosition 100 # MaximumXPosition 1300 # MinimumYPosition 100 # MaximumYPosition 1100 # # CenterX 700 # # CenterY 600 # Delta 20 # EndSubSection # # The Mouse Subsection contains the same type of entries as the # standard Pointer Section (see above), with the addition of the # DeviceName entry. # # SubSection "Mouse" # Port "/dev/mouse2" # DeviceName "Second Mouse" # Protocol "Logitech" # EndSubSection # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present Section "Monitor" Identifier "m" VendorName "m" ModelName "m" # HorizSync is in kHz unless units are specified. HorizSync 31.5 - 37.9 # VertRefresh is in Hz unless units are specified. VertRefresh 50-70 # Modes can be specified in two formats. A compact one-line format, or # a multi-line format. # These two are equivalent # ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace # Mode "1024x768i" # DotClock 45 # HTimings 1024 1048 1208 1264 # VTimings 768 776 784 817 # Flags "Interlace" # EndMode # This is a set of standard mode timings. Modes that are out of monitor spec # are automatically deleted by the server (provided the HorizSync and # VertRefresh lines are correct), so there's no immediate need to # delete mode timings (unless particular mode timings don't work on your # monitor). With these modes, the best standard mode that your monitor # and video card can support for a given resolution is automatically # used. # 640x400 @ 70 Hz, 31.5 kHz hsync Modeline "640x400" 25.175 640 664 760 800 400 409 411 450 # 640x480 @ 60 Hz, 31.5 kHz hsync Modeline "640x480" 25.175 640 664 760 800 480 491 493 525 # 800x600 @ 56 Hz, 35.15 kHz hsync ModeLine "800x600" 36 800 824 896 1024 600 601 603 625 # 1024x768 @ 87 Hz interlaced, 35.5 kHz hsync Modeline "1024x768" 44.9 1024 1048 1208 1264 768 776 784 817 Interlace # 640x480 @ 72 Hz, 36.5 kHz hsync Modeline "640x480" 31.5 640 680 720 864 480 488 491 521 # 800x600 @ 60 Hz, 37.8 kHz hsync Modeline "800x600" 40 800 840 968 1056 600 601 605 628 +hsync +vsync # 800x600 @ 72 Hz, 48.0 kHz hsync Modeline "800x600" 50 800 856 976 1040 600 637 643 666 +hsync +vsync # 1024x768 @ 60 Hz, 48.4 kHz hsync Modeline "1024x768" 65 1024 1032 1176 1344 768 771 777 806 -hsync -vsync # 1024x768 @ 70 Hz, 56.5 kHz hsync Modeline "1024x768" 75 1024 1048 1184 1328 768 771 777 806 -hsync -vsync # 1280x1024 @ 87 Hz interlaced, 51 kHz hsync Modeline "1280x1024" 80 1280 1296 1512 1568 1024 1025 1037 1165 Interlace # 1024x768 @ 76 Hz, 62.5 kHz hsync Modeline "1024x768" 85 1024 1032 1152 1360 768 784 787 823 # 1280x1024 @ 61 Hz, 64.2 kHz hsync Modeline "1280x1024" 110 1280 1328 1512 1712 1024 1025 1028 1054 # 1280x1024 @ 74 Hz, 78.85 kHz hsync Modeline "1280x1024" 135 1280 1312 1456 1712 1024 1027 1030 1064 # 1280x1024 @ 76 Hz, 81.13 kHz hsync Modeline "1280x1024" 135 1280 1312 1416 1664 1024 1027 1030 1064 # Low-res Doublescan modes # If your chipset does not support doublescan, you get a 'squashed' # resolution like 320x400. # 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio Modeline "320x200" 12.588 320 336 384 400 200 204 205 225 Doublescan # 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio Modeline "320x240" 12.588 320 336 384 400 240 245 246 262 Doublescan # 320x240 @ 72 Hz, 36.5 kHz hsync Modeline "320x240" 15.750 320 336 384 400 240 244 246 262 Doublescan # 400x300 @ 56 Hz, 35.2 kHz hsync, 4:3 aspect ratio ModeLine "400x300" 18 400 416 448 512 300 301 602 312 Doublescan # 400x300 @ 60 Hz, 37.8 kHz hsync Modeline "400x300" 20 400 416 480 528 300 301 303 314 Doublescan # 400x300 @ 72 Hz, 48.0 kHz hsync Modeline "400x300" 25 400 424 488 520 300 319 322 333 Doublescan # 480x300 @ 56 Hz, 35.2 kHz hsync, 8:5 aspect ratio ModeLine "480x300" 21.656 480 496 536 616 300 301 302 312 Doublescan # 480x300 @ 60 Hz, 37.8 kHz hsync Modeline "480x300" 23.890 480 496 576 632 300 301 303 314 Doublescan # 480x300 @ 63 Hz, 39.6 kHz hsync Modeline "480x300" 25 480 496 576 632 300 301 303 314 Doublescan # 480x300 @ 72 Hz, 48.0 kHz hsync Modeline "480x300" 29.952 480 504 584 624 300 319 322 333 Doublescan EndSection # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # Device configured by xf86config: Section "Device" Identifier "v" VendorName "v" BoardName "v" #VideoRam 1024 # Option "noaccel" # Option "no_bitblt" # Option "no_imageblt" # Option "sw_cursor" # Option "mmio" # Option "ext_fram_buf" # Option "hw_clocks" # Option "use_18bit_bus" # Textclockfreq 25.175 # Option "nolinear" # MemBase 0x03b00000 # Device section for C&T cards. # Option "suspend_hack" # Option "STN" # Option "no_stretch" # Option "no_center" # Option "use_modeline" # Option "fix_panel_size" # videoram 512 # Insert Clocks lines here if appropriate EndSection # ********************************************************************** # Screen sections # ********************************************************************** # The Colour SVGA server Section "Screen" Driver "svga" Device "v" Monitor "m" Subsection "Display" Depth 8 Modes "800x600" "640x480" "1024x768" ViewPort 0 0 Virtual 1024 768 EndSubsection Subsection "Display" Depth 16 Modes "800x600" "640x480" ViewPort 0 0 Virtual 800 600 EndSubsection # Depth 24 is totally screwed on AST J30 # Depth 32 is not supported on AST J30 EndSection